What are your ideas on How to Install a Bathtub?
Setting up a tub isn't precisely brain surgery, however it does need solid plumbing, woodworking, as well as sometimes, tiling skills. Changing an old tub with a new one is likewise a reasonably difficult project. If the old bathtub is conveniently available, the task can move speedily; if you have to open a wall surface to get rid of the old bathtub and position the brand-new bathtub, the job is much harder. In either case, the project is within a house handyman's skills, although you will certainly require an assistant to vacate the old tub and set in the new one. Make certain you have certified yourself for the work as well as fit attempting it. As opposed to hiring a service provider to take over a halfway-completed job, it is far better to consider employing one prior to you start. Opportunities are you may need an expert plumber to make tube connections.
This post will certainly aid you install a new bath tub in your bathroom if you have actually already acquired a brand-new tub and do not need to change the setup of your previous water supply pipes.
Your devices and also material checklist must comprise the following:
Planning for the Installation
Firstly, the supporting framework supplied with the bath needs to be fitted (if called for) according to the producer's instructions. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is very important to make sure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and the faucets. On a plastic bath, it is likewise sensible to fit a sustaining plate under the faucets device to avoid pressure on the bathtub.
Fit the versatile faucet connectors to the bottom of the two taps using 2 nuts and olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Ensure you utilize every one of the supplied washing machines.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bath need to currently prepare to be suited its last setting.
Removing Old Taps
If you need to change old taps with new ones as a part of your setup, after that the first thing you must do is disconnect the water supply. After doing so, switch on the faucets to drain any kind of water remaining in the system. The procedure of removing the existing faucets can be rather bothersome due to the limited gain access to that is typically the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the faucets. Have a cloth all set for the remaining water that will certainly originate from the pipelines. As soon as the supply pipes have actually been gotten rid of, use the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from turning throughout this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned of any kind of old sealing substance.
Before going on to fit the new faucets, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new faucets to fit.
Installing the Bathtub
Making use of the two wood boards under its feet, place the tub in the needed placement. The wood boards are handy in evenly spreading the weight of the bathtub over the area of the boards rather than focusing all the weight onto 4 tiny factors.
The following objective is to make sure that the tub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the bath tub up until the spirit level reads degree.
To set up taps, fit the bottom of the outermost versatile tap adapter to the proper supply pipe by making a compression sign up with; after that do the same for the various other faucet.
Turn on the water system and inspect all joints and also new pipework for leakages and tighten them if needed. Load the bathtub and likewise examine the overflow outlet and also the normal electrical outlet for leaks.
Finally, fix the bathroom paneling as described in the supplier's instruction manual. Tiling as well as securing around the bath tub should wait until the bathtub has been used a minimum of when as this will certainly resolve it right into its last setting.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic port to avoid damage to the thread. One end of the port fits on the plastic tail of the tap and the various other end gives a link to the existing supply pipes.
If you require to fit a monobloc, after that you will certainly need decreasing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, position the tap in the placing opening in the bath/basin guaranteeing that the washers remain in place in between the tap and the sink. Protect the faucet in place with the maker offered backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal tap adapters. The former type needs to be attached to the faucet ends first, tightening up only by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bathroom meets the tile, it is needed to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to break a stiff seal, triggering the water to permeate the wall surface in between the bathroom as well as the tiling, bring about difficulties with wetness and possible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your fixtures and installations. They are marketed in tubes and cartridges, and also can sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with spins of soaked paper or soft rope. Keep in mind to always load the tub with water before securing, to enable the movement experienced when the bathtub is in usage. The sealer can crack rather early if you do not take into account this activity before securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also easily available on the marketplace. It is suggested to fit the tiles utilizing water-resistant or water-proof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy more info about Tools You Need to Install a New Bathtub ? Try leaving a remark down below. We'd be delighted to find out your thoughts about this review. We hope to see you back again soon. Do you know about someone else who is interested by the subject? Why not share it. Thank you so much for going through it.
Water trouble? Dial.